Skip to Content

How to Read Your Water Meter

There are several reasons why you’d want to be able to locate and read your water meter.

First, you might be interested in just how much water you use in a day. By reading your meter at the beginning and the end of the day you can compare the two totals tell how much water you and your family used.

The second reason is to check for leaks. If you turn off all the taps in your house, look at your meter and it is still turning, chances are you have a leak somewhere.

Here are some hints to help you find and read your water meter.

Important note: Some water utilities encourage customers to read their own meter while others prohibit opening the meter box and tampering with the meter in any way. It is a good idea to check with your utility before examining your water meter.

STEP 1: Locate Your Meter

Locate Water MeterYour water meter is generally located near the curb in front of your home although in some areas (usually cold climates) it may be inside your home usually in the basement.

Outside meters are typically housed in a concrete box usually marked “water” (as shown in the photo) or in a meter pit with a cast iron lid.

Carefully remove the lid by using a tool such as a large screwdriver or pliers. Visually examine the area around the meter to make sure there are no harmful insects or other animals.

STEP 2: Read Your Water Meter

Water meters in the U.S. typically measure volume in gallons or cubic feet. One cubic foot = 7.48 gallons and 100 cubic feet = 748 gallons.

Water charges are typically based on 100 cubic feet or on 1000 gallon units.

There are two basic types of water meters — the straight-reading meter which resembles the an odometer in a car, and the round-reading meter which has several separate dials.

The “straight-reading” meter is by far the most common.

How to Read a Straight-Reading Meter

Straight-Reading Meter

Figure 2

In the meter shown in Figure 2, the reading is taken from the figures shown under the words CUBIC FEET.

The meter reads 81710.03 which is the total number of cubic feet of water recorded since the meter was installed. If the utility bills in units of 100 cubic feet they would read this meter as simply 817.

Straight-Reading Meter

Figure 3

The meter shown in Figure 3 is brand new, hence the reading for this meter is 0.00.

The small blue triangle (just to the right of the “35”) is the low flow indicator. That triangle will spin if any water is flowing through the meter. This indicator can be useful in leak detection.

Straight-Reading Meter

Figure 4

The meter in Figure 4, also cubic feet, is good example of a situation where the final number has already “turned over”. The correct reading on this meter is: 2425.92 cubic feet.

On most meters, the final digit will turn over once the big sweep hand has passed the 0.6 mark.

Note that the size of the meter is usually printed on the dial. The meter in Figure 4 is a 5/8″ meter as is shown on the dial.

How to Read a Round-Reading Meter

Round-Reading Meter

Figure 5

The meter in Figure 5 is an older style and is much less common, however there are still some of these meters in service.

This type of meter has several small dials and is a little more difficult to read than the straight-reading meter.

The dials are marked off in divisions of 10, and are read much like a clock, except that the hand on every other dial turns counterclockwise.

To read this meter, begin with the 100,000 dial and read each dial around the meter to the one foot dial.

If the hand is between numbers, use the lower number. Therefore, the dials at right register 806323.

Determining the Size of your Water Meter

Occasionally it may be necessary to determine the size of your water meter, for example, if you are designing a new irrigation system.

Water meters typically come in the following sizes: 5/8″, 3/4″ (these are the most common residential sizes), 1″, 1.5″, 2″. It is unusual to find anything larger than a 1.5 inch meter on a single-family home. The most common sizes are 5/8″ and 3/4″.

The size of the water meter is typically printed on the face of the meter. Sometimes the size is stamped into the case. For Badger Meters, model 25 = 5/8″, model 35 = 3/4″, and model 70 = 1″.

Sources: City Of Albuquerque

Josh Hurd

Donnie Austin

Tuesday 1st of September 2020

Tell me , I have a model 70 Badger meter , this meter is installed on a pool with irrigation also on this line , six days had past and the reading is 22800 , my question is : does that read 22 k or 2 k going on 3.

Josh Hurd

Wednesday 2nd of September 2020

Hello, every turn of a number in the white register measures 1,000 gallons. If the utility bills in units of 1,000 gallons they would read this meter as merely 22.

rocket gal

Thursday 13th of September 2018

Hi Josh, For the meter in Figure #4, shouldn't the read be 2426.92 especially since the sweep hand has passed 0.6 cu ft ?

Josh Hurd

Saturday 15th of September 2018

Hello, It is a tricky one. The read should be 2425.92 cubic feet, since the final number (6) has not exactly turned over. Thank you for stopping by.

JEAN VAN

Thursday 26th of October 2017

Please help me. I just moved in to Glendale and have no idea where my water meter is. My bill says it is high and I do not know how to check for leaks. I know if I find the meter and all the water is off I should not see it moving but where it is I don't know. Thank you very much

Josh Hurd

Thursday 26th of October 2017

If you've just moved in, it can be hard to find. Outdoor water meters are generally located on near the curb in front of your home at the outside stop valve. Look for a small iron or plastic cover in your driveway or garden.

This article might be useful to check for leaks: https://www.h2ouse.org/water-meter-leak-detection/